Overhanging Railless Up-and-Over Garage Door

Overhanging Railless Up-and-Over Garage Door

A one-piece garage door with no rail under the ceiling that swings out in front of the facade and then tips into the garage until it lies under the ceiling. Door width and height, Leaf colour, Operator or manual

Details

Category: Garage Doors › Up-and-Over Doors

By Huu Khanh Nguyen · Updated November 14, 2026

Parameters

NameDefaultUnit
Overall frame width2480mm
Overall frame height2195mm
Opening0°
Leaf finishwhite
Rib Pitch100mm
Arm pin height on the leaf (Low)0.08 * (height - 93)mm
Arm pivot depth behind the frame plane (Low)((-125 - armLowPinZ) / 2) - 0.187 * (height - 48 - armLowPinZ)mm
Arm pivot height (Low)((armLowPinZ + height - 18) / 2) + 0.187 * (-75 - armLowPinZ)mm
Lift arm length between its pins (Low)Math.sqrt((armLowPivotY + 25) * (armLowPivotY + 25) + (armLowPivotZ - 15 - armLowPinZ) * (armLowPivotZ - 15 - armLowPinZ))mm
Pin circle centre y (Low)armLowPivotY + 25 * Math.cos(opening * Math.PI / 180) + armLowPinZ * Math.sin(opening * Math.PI / 180)mm
Pin circle centre z (Low)armLowPivotZ + 25 * Math.sin(opening * Math.PI / 180) - armLowPinZ * Math.cos(opening * Math.PI / 180)mm
Arm pin height on the leaf (High)0.575 * (height - 93)mm
Arm pivot depth behind the frame plane (High)((-125 - armHighPinZ) / 2) - 0.572 * (height - 48 - armHighPinZ)mm
Arm pivot height (High)((armHighPinZ + height - 18) / 2) + 0.572 * (-75 - armHighPinZ)mm
Lift arm length between its pins (High)Math.sqrt((armHighPivotY + 25) * (armHighPivotY + 25) + (armHighPivotZ - 15 - armHighPinZ) * (armHighPivotZ - 15 - armHighPinZ))mm
Pin circle centre y (High)armHighPivotY + 25 * Math.cos(opening * Math.PI / 180) + armHighPinZ * Math.sin(opening * Math.PI / 180)mm
Pin circle centre z (High)armHighPivotZ + 25 * Math.sin(opening * Math.PI / 180) - armHighPinZ * Math.cos(opening * Math.PI / 180)mm
Leaf offset y((dy, dz) => ((d) => ((chord) => cLowY + chord * dy / d - Math.sqrt(armLowLength * armLowLength - chord * chord) * dz / d)((armLowLength * armLowLength - armHighLength * armHighLength + d * d) / (2 * d)))(Math.sqrt(dy * dy + dz * dz)))(cHighY - cLowY, cHighZ - cLowZ)mm
Leaf offset z((dy, dz) => ((d) => ((chord) => cLowZ + chord * dz / d + Math.sqrt(armLowLength * armLowLength - chord * chord) * dy / d)((armLowLength * armLowLength - armHighLength * armHighLength + d * d) / (2 * d)))(Math.sqrt(dy * dy + dz * dz)))(cHighY - cLowY, cHighZ - cLowZ)mm